Recent Activity

Activity stream for all registered members at C-Bus Forums.

  1. Diggerz liked oracle's post in the thread Remote access - Zerotier or Tailscale.

    Hi all, I wanted to share some handy utilities and setup workflows I've been playing with to get secure remote access to a SHAC...

    Oct 12, 2026 at 8:34 PM

  2. Wonkey replied to the thread eDLT failure and replacement issues.

    Contact tech support or your local Clipsal rep. they should be able to sort out repair. With regard to the other eDLT are the buttons...

    Oct 12, 2026 at 2:13 PM

  3. oracle posted a new thread.

    Remote access - Zerotier or Tailscale

    Hi all, I wanted to share some handy utilities and setup workflows I've been playing with to get secure remote access to a SHAC...

    Forum: C-Bus Automation Controllers

    Oct 12, 2026 at 11:13 AM

  4. theboyg posted a new thread.

    eDLT failure and replacement issues

    I've had one of my eDLTs fail, screen went blank, appears on the network, buttons do nothing. Connected the USB to try to reflash the...

    Forum: C-Bus Wired Hardware

    Oct 12, 2026 at 9:37 AM

  5. Trevor replied to the thread NEO KEYM8 1.4.0 – Unit Transfer failed 45127, dimmers program OK.

    Just a quick note on measuring the voltage on each Cbus wire to ground.... The voltages must be balanced ie the same on each wire to...

    Oct 11, 2026 at 5:45 AM

  6. Wonkey replied to the thread NEO KEYM8 1.4.0 – Unit Transfer failed 45127, dimmers program OK.

    I agree the new SLCC is not the best, but it's the future. You can unlock each bit of the application and make it larger to work on,...

    Oct 10, 2026 at 11:00 PM

  7. OldDogNewTrick replied to the thread NEO KEYM8 1.4.0 – Unit Transfer failed 45127, dimmers program OK.

    Thanks again Wonkey....Yes you're right my initial diagnosis was off...by disconnecting a cbus cable what I'd actually done was remove a...

    Oct 10, 2026 at 11:27 AM

  8. lcrowhurst replied to the thread How quickly can you build an automation controller?.

    For my KNX clients using an LM5 I use Zerotier, for my CBus Clients using AC2 - on unifi networks I use Teleport/wireguard. So I am very...

    Oct 9, 2026 at 1:40 AM

  9. oracle replied to the thread BATTERY.

    RCD should have no effect on the cbus but for reference the current RCD regulations in Australia—under AS/NZS 3000, Type AC RCDs are...

    Oct 8, 2026 at 2:24 AM

  10. LightingControlProgrammer replied to the thread BATTERY.

    Monitor cbus indication light, if it flickers id suspect internal power supplier intermittent failure, during the power isolations and...

    Oct 7, 2026 at 12:38 PM

  11. martymonster replied to the thread 5500AC2 - new to programming it - Automations setup query.

    I finally found how to get it to show

    Oct 7, 2026 at 6:37 AM

  12. steveGR replied to the thread BATTERY.

    Thanks for the quick response, Graham I do have a touch screen and use the tool kits to alter my network & data now and then, but...

    Oct 7, 2026 at 1:20 AM

  13. Graham Lamb replied to the thread BATTERY.

    Hi I am running a 30Kwh Alpha Battery and 5Kw inverter with 14 Kw solar panels and cbus runs everything and I have no problems at all....

    Oct 7, 2026 at 1:12 AM

  14. oracle replied to the thread How quickly can you build an automation controller?.

    Hey Laurence, how do you give remote secure access, out of curiousty - I have made some ipk one to enable zerotier(installs missing...

    Oct 6, 2026 at 11:55 PM

  15. steveGR posted a new thread.

    BATTERY

    Hi folks Not sure if there is any relation here, but about one month ago I had a Goodwe Battery installed at home onto my existing solar...

    Forum: General Discussion

    Oct 6, 2026 at 11:51 PM
Show older items
Loading...