Config change messages??

Discussion in 'C-Bus Toolkit and C-Gate Software' started by Ingo, Nov 14, 2007.

  1. Ingo

    Ingo

    Joined:
    Dec 2, 2006
    Messages:
    290
    Likes Received:
    1
    Location:
    South Africa
    I see lots of config change messages from both my light sensors. Below is an output from c-gate. Any ideas why these messages are logged? All I am doing with the one light sensor is setting a garden light group and polling both with homegate for a monitor indicator. Oh, the Logic reads these as well, every 240s.

    20071114-165212 836 //MIDSTRM/254/p/14 2b63c8a0-5218-102a-8008-da2423f3aff5 unit configuration changed (2 changes)
    20071114-165507 836 //MIDSTRM/254/p/13 7733c7e0-8a17-1029-b82a-948a5022f37d unit configuration changed (2 changes)
    20071114-165510 836 //MIDSTRM/254/p/14 2b63c8a0-5218-102a-8008-da2423f3aff5 unit configuration changed (2 changes)
    20071114-165746 836 //MIDSTRM/254/p/13 7733c7e0-8a17-1029-b82a-948a5022f37d unit configuration changed (2 changes)
    20071114-165749 836 //MIDSTRM/254/p/14 2b63c8a0-5218-102a-8008-da2423f3aff5 unit configuration changed (2 changes)
    20071114-170027 836 //MIDSTRM/254/p/13 7733c7e0-8a17-1029-b82a-948a5022f37d unit configuration changed (2 changes)
    20071114-170029 836 //MIDSTRM/254/p/14 2b63c8a0-5218-102a-8008-da2423f3aff5 unit configuration changed (2 changes)
    20071114-170259 836 //MIDSTRM/254/p/13 7733c7e0-8a17-1029-b82a-948a5022f37d unit configuration changed (2 changes)
    20071114-170302 836 //MIDSTRM/254/p/14 2b63c8a0-5218-102a-8008-da2423f3aff5 unit configuration changed (2 changes)
    20071114-170600 836 //MIDSTRM/254/p/13 7733c7e0-8a17-1029-b82a-948a5022f37d unit configuration changed (2 changes)
     
    Ingo, Nov 14, 2007
    #1
  2. Ingo

    NickD Moderator

    Joined:
    Nov 1, 2004
    Messages:
    1,427
    Likes Received:
    64
    Location:
    Adelaide
    On these units (and also the old temperature sensor), the light level (or temperature) was never available via a broadcast on C-Bus. The monitor components in the logic engine or touchscreen actually have to use C-Bus configuration messages to extract the light level (or temperature) readings from the units.

    I think C-Gate is actually just displaying the fact that there are configuration messages occurring when the logic reads the light level, not that the configuration has actually changed.

    Nick
     
    NickD, Nov 15, 2007
    #2
  3. Ingo

    Ingo

    Joined:
    Dec 2, 2006
    Messages:
    290
    Likes Received:
    1
    Location:
    South Africa
    What I'll do is to shutdown HomeGate but keep C-Gate running and see what happens.
     
    Ingo, Nov 15, 2007
    #3
  4. Ingo

    Ingo

    Joined:
    Dec 2, 2006
    Messages:
    290
    Likes Received:
    1
    Location:
    South Africa
    I checked a bit further and this is what I found. If I start only CGate then no messages are received. If I start HomeGate with a default empty template (aura), these messages start appearing. It doesn't matter which project I choose, the messages keep appearing.

    20071118-170936 836 //TEST/254/p/14 - unit configuration changed (2 changes)
    20071118-170938 836 //TEST/254/p/15 - unit configuration changed (2 changes)
     
    Ingo, Nov 18, 2007
    #4
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads

  1. Access.TXT Config file

  2. Third Party Barcode Reader Config

  3. CNI config for Touchsoft App

  4. Wiser Power Measurement 'Virtual Channel' config for Dual Solar

  5. CBUS Training and Config for personal install

  6. Reset Wiser IP addresses and router config

  7. Help me!! Config plug adaptor and Remote Control

  8. Problem with Wiser Router Config

Loading...