DLT Text

Discussion in 'C-Bus Toolkit and C-Gate Software' started by Dave Byron, Sep 5, 2006.

  1. Dave Byron

    Dave Byron

    Joined:
    Aug 3, 2004
    Messages:
    835
    Likes Received:
    0
    Location:
    Casurina
    Why does the DLT text not show up on "trigger app" ??


    dave
     

    Attached Files:

    Dave Byron, Sep 5, 2006
    #1
  2. Dave Byron

    Don

    Joined:
    Aug 4, 2004
    Messages:
    429
    Likes Received:
    0
    Location:
    Townsville, Australia
  3. Dave Byron

    Dave Byron

    Joined:
    Aug 3, 2004
    Messages:
    835
    Likes Received:
    0
    Location:
    Casurina
    Dave Byron, Sep 5, 2006
    #3
  4. Dave Byron

    wanricky

    Joined:
    Sep 12, 2005
    Messages:
    219
    Likes Received:
    0
    create some action selectors for a few trigger addresses and try.
     
    wanricky, Sep 5, 2006
    #4
  5. Dave Byron

    Dave Byron

    Joined:
    Aug 3, 2004
    Messages:
    835
    Likes Received:
    0
    Location:
    Casurina
    When powered up PC this morning all was ok so went looking for sequence that cause the problem.

    goto trigger control in left pane
    open up groups in left pane
    open a group and look at dlt text on a action selector
    goto network and dlt labels
    now when try to open trigger control fails

    can reproduce the error every time.


    It will still show DLT text on a single group or action selector - pic

    dave
     

    Attached Files:

    Last edited by a moderator: Sep 5, 2006
    Dave Byron, Sep 5, 2006
    #5
  6. Dave Byron

    wanricky

    Joined:
    Sep 12, 2005
    Messages:
    219
    Likes Received:
    0
    Would it be address over-flow? There are 255 Trigger addresses, with maybe 10 action selector each, so there are 2550 labels to be displayed....Or toolkit may take an hour to load all these labels......:eek:
     
    wanricky, Sep 6, 2006
    #6
  7. Dave Byron

    Dave Byron

    Joined:
    Aug 3, 2004
    Messages:
    835
    Likes Received:
    0
    Location:
    Casurina
    Got it – when toolkit show the DLT text on a single group and its in red (too long) when you save it does not write the truncated text, it writes nothing.
    Now if all the text entries are too long when you open full DLT window it does not show the default DLT text.
    It wants at least one valid DLT entry.

    dave
     
    Last edited by a moderator: Sep 6, 2006
    Dave Byron, Sep 6, 2006
    #7
  8. Dave Byron

    Dave Byron

    Joined:
    Aug 3, 2004
    Messages:
    835
    Likes Received:
    0
    Location:
    Casurina
    DLT Labelling
    If you create a new database and add one group in the lighting and trigger applications. Now go to the main DLT editing window and turn off the only show in units option.
    In lighting application it shows the group text but if you go to the trigger group nothing.
    Trigger DTL text is only shown if there is text there already.

    dave
     
    Dave Byron, Sep 9, 2006
    #8
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.